| View previous topic :: View next topic |
| Author |
Message |
MAJDI
Joined: 08 Dec 2008
Posts: 8
|
 Posted: Sun Jan 04, 2009 7:53 am Post subject: connection to carrier by usb connection through cell phone |
 |
|
Dear All
In connection wizard in NotePager show:
“NotePager Pro can send message to carrier by using modem or internet connection”
I connect mobile phone to pc by usb cable,
So
Is it possible NotePager Pro connect to carrier via GSMAT protocol and with my mobile phone that connected to pc by usb cable no with modem?
my mobile phone is Nokia 3230 and i can run AT command in hyperterminal with usb connection. also AT+CMGF=1 is ok in this environment.
Thanks.
Mojtaba
|
|
| Back to top |
|
Tech Support
Joined: 25 Aug 2003
Posts: 4387
|
| Posted: Mon Jan 05, 2009 11:02 am Post subject: |
|
|
Sure, as long as you install the phone into Windows as a modem. Windows has to assign your phone a COM port before NotePager Pro can use it.
After you've done that, all you have to do is open the program and do this:
1) Go to Tools - Settings - Modem.
2) Set the Modem Port to the COM port assigned to your phone.
3) Click on Apply.
To configure a GSM-AT Carrier:
1) Go to Carriers - Add.
2) Name the Carrier: GSM
3) Set the protocol to: GSM-AT
4) Mirror your phone's connection requirements for baud rate, parity, data bits, and stop bits. If you're unsure what these are, please reference your phone's manual or contact the phone's manufacturer.
5) Click on Apply.
When adding a recipient to use the GSM carrier, use the person's 10 digit cel phone number (no spaces or dashes) as the ID/PIN. |
|
| Back to top |
|
MAJDI
Joined: 08 Dec 2008
Posts: 8
|
| Posted: Thu Jan 08, 2009 5:27 am Post subject: notepager pro can not talk with your modem! |
|
|
Dear tech support
thanks for your reply
When I change modem port (in Tools - Settings – Modem) and set parameters for baud rate, parity, data bits, and stop bits in GSM-AT protocols same as parameters in hyperterminal , the system can not send message and it show in dialog window that system can not talk with modem,
Although I can communicate in hyperterminal with mobile phone and with same parameters, and can do AT command.
my mobile phone model is Nokia 3230.
Please help me
Regards
Majdi
|
|
| Back to top |
|
Tech Support
Joined: 25 Aug 2003
Posts: 4387
|
| Posted: Thu Jan 08, 2009 9:58 am Post subject: |
|
|
| What COM port did the modem install to? |
|
| Back to top |
|
MAJDI
Joined: 08 Dec 2008
Posts: 8
|
| Posted: Thu Jan 08, 2009 11:22 pm Post subject: |
|
|
| it has been installed on com port 6
|
|
| Back to top |
|
Tech Support
Joined: 25 Aug 2003
Posts: 4387
|
| Posted: Fri Jan 09, 2009 4:36 pm Post subject: |
|
|
| Did you receive the email I sent earlier today? It has a list of steps for a test I'd like you to run. |
|
| Back to top |
|
MAJDI
Joined: 08 Dec 2008
Posts: 8
|
| Posted: Sat Jan 10, 2009 7:00 am Post subject: |
|
|
Hi
Yes i did, i sent you the result (led in vbterm was green, but notepage pro can not talk with modem yet).
in my work pc the port that assigned to mobile handset that cnnected by usb cable is port8(not port6) and i did setting with this new port.
Regards
majdi
|
|
| Back to top |
|
|
