View previous topic :: View next topic |
Author |
Message |
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 3:57 pm Post subject: How to test SMS from Note Page |
|
|
Hi,
I have Note Page configured with AT&T Tap.
I have recipients configured.
I'm trying to test outgoing SMS out. Is there a tool or set of commands that I can run to test this?
|
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 4:02 pm Post subject: |
|
|
To test it, all you should need to do is click on the name of a Recipient in the Recipients list to move them over to the Selected Recipients list. Then type a message in the "Message Text" box and hit Send. The Connection Monitor will display the command and response sequence for the delivery attempt and will record whether or not the message was successful. |
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 4:08 pm Post subject: |
|
|
Ok. It seems that the connection to carrier is started, the connection using TAP is initiated, but the logs keep displaying Attempting to reset modem. Eventually the logs display Hanging up modem.
Obviously something is going on with the modem.
I'm assuming the modem is not starting or else it doesn't support this type of traffic?
|
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 4:12 pm Post subject: |
|
|
It sounds like the program is referencing a COM port other than the one the modem is tied to. So, here's what you'll want to do:
1) Go in to the Control Panel in Windows.
2) Go to Phone and Modem.
3) Go under the Modems tab and make a note of the COM port the modem is tied to.
4) In NotePager Pro, go to Tools - Settings - Modem.
5) Set the "Modem Port" field to match the COM port of the modem.
6) Click on Apply and see if the same behavior is present. |
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 4:25 pm Post subject: |
|
|
The modem is connected on COM3. I confirmed this through Control Panel > Modems and also through device manager.
I also ran a modem scan in Note Page and confirmed that only COM3 is checked.
I queried the modem using the tool available in the modem properties and I get
ATQ0V1E0 Success
Iit recognizes the modem type.
AT#CLS=? is not supported
ATI2 Success
The logs in Note Page show first
Sent: AT<CR>
Attempting to reset modem.
This loops three times. Then it tries a different command
Sent: ATH0<CR>
Tries three times until it reaches the attempts limit.
So it looks like the modem answers when tested from Windows, but it doesn't answer when Note Page calls it.
|
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 4:26 pm Post subject: |
|
|
What make and model of modem are you trying to use? |
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 4:29 pm Post subject: |
|
|
Zoom Technologies V.92
Series 0375
btw, in your previous post you mentioned Tools > Settings
but I couldn't really find those settings.
|
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 4:38 pm Post subject: |
|
|
I'm also trying with a US Robotics 5633
Both are USB modems (a little old, but device/drivers are still recognized by Windows). Note that in both cases I'm loading drivers manually from manufacturer.
|
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 4:43 pm Post subject: |
|
|
Wait, are you using PageGate or NotePager Pro? If you're using NotePager Pro, you should have a Tools menu with several options. If you're using PageGate and the PageGate client, that setting is in an entirely different location. |
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 4:44 pm Post subject: |
|
|
Also, I've never been able to get a Zoom modem to connect to a TAP system before. There's something about the chipset they use, and I don't know what it is, that just cannot handle handshaking with a TAP system. I would really recommend not using that modem, go with the USR modem. |
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 4:49 pm Post subject: |
|
|
My bad. I'm using PageGate.
Ok. I'm testing with the USR again.
Where's the tools > modem setting that you spoke of
|
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 4:53 pm Post subject: |
|
|
Ah, that makes more sense. Originally, I assumed you were using NotePager Pro since the thread was in the NPP portion of the forum.
Anyhow, what you'll want to do is open the PageGate Admin on the PageGate Server. Then:
1) Go to Connectors - Connector 1 - Settings.
2) Set the "Serial Port" field to match the COM port of the modem.
3) Make sure Direct Connect is NOT checked.
4) Click on Apply. |
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Fri Jan 24, 2014 5:12 pm Post subject: |
|
|
Ok. This looks better. It's initiating a connection but now I'm getting no response from the carrier. I'm checking with AT&T to determine if it's an issue on their end.
Btw, I see a service for PageGate Connector1 under Windows services.
Do I have to set that service to start automatically given that I linked the modem to Connector1 in the application?
|
|
Back to top |
|
Tech Support
Joined: 25 Aug 2003 Posts: 4367
|
Posted: Fri Jan 24, 2014 5:16 pm Post subject: |
|
|
What TAP number are you using? The best to use for AT&T is 18009094602.
As for the services, no. The only PageGate service that should have an Automatic startup type is the service named PageGate. Any sub-services (Scheduler, Connectors, Modules) are started in a very specific order controlled by the main PageGate service. |
|
Back to top |
|
modemhead
Joined: 03 Jan 2014 Posts: 18 Location: NY
|
Posted: Mon Feb 03, 2014 4:41 pm Post subject: |
|
|
The alternate ATT phone number that you provided seems to have done the trick. Will test further and report IF I have issues.
|
|
Back to top |
|
|