pagegate GetTap is not sending page messages

[Robertk]

========================================
1/16/2007 4:47:16 PM Start connection to carrier: ATT
1/16/2007 4:47:16 PM Connect using TAP protocol
1/16/2007 4:47:16 PM Setting communication parameters
1/16/2007 4:47:17 PM Attempting to reset modem
1/16/2007 4:47:19 PM Sent:AT<CR>
1/16/2007 4:47:19 PM Received:<CR><LF>OK<CR><LF>
1/16/2007 4:47:20 PM Modem reset
1/16/2007 4:47:20 PM Attempting to send dialer init string
1/16/2007 4:47:20 PM Sent:AT&FQ0V1X4&D2N0+MS=V22,0<CR>
1/16/2007 4:47:20 PM Received:<CR><LF>OK<CR><LF>
1/16/2007 4:47:21 PM Dialer init string sent
1/16/2007 4:47:21 PM Dialing carrier
1/16/2007 4:47:21 PM Sent:ATDT92617099<CR>
1/16/2007 4:47:29 PM Waiting for connection
1/16/2007 4:47:40 PM Received:<CR><LF>CONNECT 1200<CR><LF>
1/16/2007 4:47:40 PM Connected to carrier
1/16/2007 4:47:40 PM Waiting for protocol initialization
1/16/2007 4:47:44 PM Received:ID=<LF><CR>
1/16/2007 4:47:44 PM TAP protocol detected
1/16/2007 4:47:45 PM Sent:<ESC>PG1<CR>
1/16/2007 4:47:47 PM Received:<ACK><CR>Processing - Please wait<LF><CR><ESC>[p<CR>
1/16/2007 4:47:47 PM Received:<ACK><CR>Processing - Please wait<LF><CR><ESC>[p<CR>
1/16/2007 4:47:47 PM Automatic TAP mode accepted
1/16/2007 4:47:47 PM ----------------------------------------
1/16/2007 4:47:47 PM Working on message to: att from: s603973
1/16/2007 4:47:47 PM Formatting message
1/16/2007 4:47:47 PM Message contained in single packet
1/16/2007 4:47:47 PM Message contained in single block
1/16/2007 4:47:48 PM Sending block
1/16/2007 4:47:48 PM Sent:<STX>4501061<CR>s603973:test<CR><ETX>529<CR>
1/16/2007 4:47:49 PM Received:<LF><CR>Record not found for ID: 4501061 <CR><RS><CR>
1/16/2007 4:47:49 PM Bad ID or message content. Message aborted
1/16/2007 4:47:49 PM Permanent failure. Message will not be retried
1/16/2007 4:47:49 PM FAILED Stn:10 To:att Frm:s603973 Msg:test
1/16/2007 4:47:49 PM Sent:<EOT><CR>
1/16/2007 4:47:49 PM Attempting to hang up modem
1/16/2007 4:47:52 PM Sent:AT<CR>
1/16/2007 4:47:52 PM Received:<CR><LF>OK<CR><LF>
1/16/2007 4:47:52 PM Modem hung up

[Tech Support]

AT&T uses a 10 digit number for the recipient. Currently, you have your recipient set up for a 7 digit:

1/16/2007 4:47:48 PM Sending block
1/16/2007 4:47:48 PM Sent:<STX>4501061<CR>s603973:test<CR><ETX>529<CR>
1/16/2007 4:47:49 PM Received:<LF><CR>Record not found for ID: 4501061 <CR><RS><CR>

If you put the area code on, it should work okay.