| |
Search found 12 matches |
Author | Message |
---|---|
Topic: wont send message | |
Poncho67 Replies: 1 Views: 10260 |
Forum: General Questions and Announcements Posted: Wed Jul 27, 2005 9:49 am Subject: TAP |
You need to obtain a TAP number from your paging company.
The software would then use TAP to deliver the text message. Right no, it sounds like you are dialing your pager's phone number. That is fine for numerical messages only. |
|
Topic: Notepager32 sends but says its bad. | |
Poncho67 Replies: 4 Views: 12385 |
Forum: NotePager Pro Support Posted: Mon Jul 25, 2005 5:03 am Subject: Notepager32 sends but says its bad. |
Increase the Baud up to 2400 or 9600 and use "(auto)" for Init String. | |
Topic: Sending an SMS | |
Poncho67 Replies: 1 Views: 7499 |
Forum: PageGate Support Posted: Fri Jul 22, 2005 10:24 am Subject: Sending an SMS |
GSM Carrier settings do not require a telephone number or Init String.
You do need to enter ID/Pins for Recipients (usually the phone number of the device you are sending a message to). |
|
Topic: Notepager32 sends but says its bad. | |
Poncho67 Replies: 4 Views: 12385 |
Forum: NotePager Pro Support Posted: Fri Jul 22, 2005 10:22 am Subject: Notepager32 sends but says its bad. |
Looks like your modem did not receive the terminal's acknowledgement response<ACK> after NP32 sent the message block.
Try using this Init Sting: AT&FQ0V1X4&D2N0+MS=V22 If it continues, try dropping the Baud Rate to 300 and reset the Carrier Init String to "(auto)". |
|
Topic: ID/PIN number | |
Poncho67 Replies: 1 Views: 8144 |
Forum: NotePager Pro Support Posted: Fri Jul 22, 2005 10:18 am Subject: ID/PIN number |
Try removing the "1" from the ID/Pin. Verizon accepts 10 digit ID/Pins for SNPP.
Otherwise, contact Verizon to verify you can receive pager messages via SNPP. Verizon does NOT support SNPP for their Cell phones. |
|
Topic: direct connection | |
Poncho67 Replies: 4 Views: 12452 |
Forum: PageGate Support Posted: Thu Jul 14, 2005 5:09 am Subject: direct connection |
The dialer log clearly indicates that the terminal's serial port is configured for Manual Entry Mode.
I can't help you with the actual settings for the Terminal, although I would guess that the "01" at the end of the line hex below, be changed to "00" (for the port that you are using). 0D 00 02 1E 01 ; force manual entry mode 0=no, 1=yes (8a4+) |
|
Topic: direct connection | |
Poncho67 Replies: 4 Views: 12452 |
Forum: PageGate Support Posted: Wed Jul 13, 2005 2:26 pm Subject: direct connection |
Could be that the serial port on the Zetron is not configured for TAP, but is configured for Manual entry. | |
Topic: direct connection | |
Poncho67 Replies: 4 Views: 12452 |
Forum: PageGate Support Posted: Wed Jul 13, 2005 1:11 pm Subject: direct connection |
Can you post a direct connection attempt from your Dialer log (PGDial1.log)? | |
Topic: Trying unsuccessfully to connect to Airtouch | |
Poncho67 Replies: 2 Views: 10446 |
Forum: NotePager Pro Support Posted: Mon Jul 11, 2005 9:11 pm Subject: Trying unsuccessfully to connect to Airtouch |
Looks like the Airtouch TAP termnal cannot handle 2400 Baud with your modem.
a) Drop the Carrier Baud Rate to 1200 and b) Set the Carrier Init String to "(auto)". |
|
Topic: message will not quit | |
Poncho67 Replies: 2 Views: 9048 |
Forum: NotePager Pro Support Posted: Wed Jul 06, 2005 12:57 pm Subject: message will not quit |
Try shutting down your NotePager Pro.
If the message continues, it is not a software problem. |
|
Topic: Error #339Component 'comdlg32.ocx not correctly registered | |
Poncho67 Replies: 1 Views: 9379 |
Forum: PageGate Support Posted: Wed Jul 06, 2005 12:53 pm Subject: Try manually registering the file |
Try manually registering the file.
Type this on the commandline: "regsvr32 comdlg32.ocx" You should receive a message box that states: "DllRegisterServer in comdlg32.ocx succeeded." Repeat for any other "dll" or "ocx" files that you may get a similiar error on. |
|
Topic: Unable to send messages from Windows 2003 server | |
Poncho67 Replies: 5 Views: 12972 |
Forum: PageGate Support Posted: Thu Jun 23, 2005 1:31 pm Subject: Solution? |
Was there a solution? | |
All times are GMT - 5 Hours |